Perfect panel glue-ups – FineWoodworking


Video

Jointing with glue-ups in mind is a precise business. Watch how Mike Pekovich breaks it down into simpler steps.


Aug 10, 2022

Sponsored by Grizzly Industrial



Jointing

Check that your jointer cuts properly before you use it. In case of sniping or tapering, adjust the outfeed table. In addition to this, you’ll want to make sure the jointer blades are sharp. Dull blades have a tendency to burnish wood, compromising glue absorption and the subsequent strength of the joint.

It’s not imperative, but if possible, the fence should be perfectly squared with the outfeed table. Despite differences in techniques, the geometric properties of handplaning also apply here with adjacent boards. In order to make them comply, alternate the faces that meet the jointer fence. Use chalk to help keep track of the face directions.

First, butt two adjacent boards together. On one side of the joint line, mark the board surface with an ‘I’ to indicate that the face of that board must run inside, against the fence. Mark the opposite side of the joint line with an ‘O’ to indicate that it must face outside, away from the fence. Once all of the adjacent boards have been respectively marked, it’s simply a matter of running them through the jointer while making sure the correct faces of the boards meet the fence.

When all of the adjacent boards are butted after jointing, the supplemental Y angle principle ensures that the surfaces are flush and flat. This approach is typically more reliable than running a pair of boards folded together through the jointer.

Clamping

Now that the boards are flat, straight, marked, and arranged to your satisfaction, it’s time to start considering the gluing process. Some prep is required first, starting with making sure the clamps have a flat and true work surface to rest on during the glue-up. An uneven or twisted work surface will result in uneven clamp placement, and ultimately an uneven tabletop. By using a straightedge across both the length and width of your work surface, you can easily ensure that it’s flat in both directions. Additionally, winding sticks will help determine if the surface is twisted. If it is, you can usually add a shim under one or two legs to even out the surface.

Begin laying out the clamps. Either pipe or bar clamps will work, as long as they’re straight. Spanning across all of the clamps with a straightedge is also recommended. If the straightedge rocks or a gap appears between the straightedge and the pipe, replace the offending clamps.

Gluing

Apply a bead of yellow glue along the entire edge, then spread the glue using a stick. Next, press the two glued edges together and slide the boards side to side a little to fully spread the glue. Keep moving efficiently from one board to the next, making sure with each joint that the boards are sticking together as planned.

When all of the edges have been assembled, tighten the lower clamps only enough to apply light but firm pressure. Check the underside of the tabletop to make sure it’s sitting flat on the clamps. If it isn’t, a few judicious raps from the deadblow hammer should solve the problem. Starting from the middle of the tabletop and working toward the ends, begin applying additional pressure to the lower clamps. If the ends of any boards are misaligned, temporarily mount C-clamps at both ends of the tabletop, with the pads of the clamps spanning each joint. Since the steel pads only remain there temporarily, they won’t stain the wood.

Once all the faces of the boards align, apply additional pressure to the end pipe clamps, then remove the C-clamps. Next, add the top clamps. Once all of the top clamps are in position, it’s just a matter of tightening them snugly. Check again to ensure that the tabletop is flat on the pipes and that all of the clamps are tightened– but don’t over tighten.

Invariably, the pressure from the clamps is going to squeeze some glue from the joints. Allow enough time, usually about 15 minutes, for the glue to turn rubbery. Then, using a putty knife, the glue will scrape off with relative ease.

Sign up for eletters today and get the latest techniques and how-to from Fine Woodworking, plus special offers.

Get woodworking tips, expert advice and special offers in your inbox

×





We will be happy to hear your thoughts

Leave a reply

While Windows Shopping
Logo
Enable registration in settings - general
Compare items
  • Total (0)
Compare
0
Shopping cart